1. Before initial operation of your new American System take a few minutes to read instructions on its operations.
2. Never allow the whirlpool system to run without sufficient water in the tub. The pump is designed to be cooled by the water. Continued operation without water could damage seal or impeller.
3. Never allow small children in the bathtub without proper supervision.
4. Don’t place small articles in the bathtub that could possibly enter into the jets or suction area.
5. If your system is operated by a timer or wall switch always set timer or switch while out of the bathtub.
6. If your system is operated by an air switch it can be turned on or off at any time while in the bathtub.
7. Make sure the eyeballs of all jets are turned in a downward position.
8. Do not add bubble bath, soaps, or oils to the water.
9. While in the bathtub you may start making the necessary adjustments for the most comforting and relaxing bathing experience:
   • Adjust the eyeball for the directional flow that most suits you.
   • By adjusting the Air Control(s) you can determine your own air and water mixture. The Air Control closed all the way will eliminate air from your jets. Open your control(s) a slight turn at a time until the suitable massage action is determined.
10. Be careful not to overdo your stay in the bathtub.

To properly clean an acrylic bathtub it is recommended to wipe the surface with a damp cloth or sponge using, Clean*Way, household soap or liquid detergent. Stubborn dirt or stains may be removed using Spic & Span in powder form or equivalents. DO NOT use any cleaning products containing abrasive or solvents since these could dull the brilliant surface or cause crazing. Products like Bon-Ami, Comet, Ajax, Scrubbing Bubbles, Lysol, or Windex are not recommended. Harsh chemicals  with any alcohol, amonia, or acid content should never be used on acrylic surfaces which can cause crazing. Avoid using aerosol products on the bath surface.

Whirlpool Systems: It is necessary to regularly clean your American Acrylic Whirlpool System. Normal cleaning should be performed once a month. Even though most of our products, (including the external piping), contain built in anti-microbial additives, we suggest cleaning the piping of the system.

Fill your bathtub with warm water.

1. Add 1 cup of Clean*Way which can be purchased directly off this website.
2. Turn your system on and allow it to run for about 10 minutes.
3. Drain bathtub.
4. Fill your tub once again with water and allow your system to run another 10 minutes, purging all soap from the lines.
5. Drain tub. You should now have a clean and sanitary whirlpool system.

All products need to be tested for proper drainage and/or leaks prior to final installation by your installer.

Installation should be performed by a licensed contractor. 

All products need to be tested for proper drainage and/or leaks prior to final installation by your installer.
Whirlpool system, Air massage system, or vibrosonic system requires a 20Amp GFCI dedicated circuit and an access panel.

To all original purchasers of its products, American Acrylic & Injections, Inc., 419 Welch Drive, Farmersville, TX 75442, warrants its motors free from defects in material and workmanship for a period of two years and limited life time warranty on the pump and whirlpool components.

Products which fail or become defective during the warranty period, except as a result of freezing, accident, negligence, improper installation, use, or care, shall be repaired or replaced at our option, without charge within 90 days of receipt of defective products, barring unforeseen delays.

American Acrylic & Injection, Inc. shall not be responsible for cartage, removal, and/or re-installation labor, or any other such costs incurred in obtaining warranty replacements.

Some states do not allow a limitation on how long an implied warranty lasts, or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusion may not apply to you.

This warranty gives you specific legal rights, and you may also have other rights which vary from state to state.

American Acrylic & Injection, Inc. is not responsible for loss of the system or inconvenience, loss or damage to personal property or their consequential damage.

American Acrylic & Injection, Inc. extends a limited lifetime warranty to all original purchasers of its pumps that they are free from defects in materials and workmanship. Note: Alteration of pump location voids warranty.

The limited lifetime warranty applies only on the plastic pump as manufactured by American Acrylic & Injection, Inc. and specifically excludes all components and/or parts which are accessories therein. The motor/air switch is warranted for a period of two (2) years by the manufacturer to the original purchaser from the date of purchase.

Products which fail or become defective during warranty period shall be repaired or replaced at our option without charge and within 60 days of receipt of the defective product.

In case of removal or replacements, the purchaser assumes the responsibility for labor expenses for service, removal, and re-installation; unless a service labor agreement exists between the purchaser and dealer.

The warranties made above are only warranties on the separate components of the system. Improper or negligent installation of your tub with the plumbing, electrical hook-up connections, or alterations or modifications to the system are not covered by any warranty, expressed or implied. This is the only expressed or implied warranty given by American Acrylic & Injection, Inc.

To obtain warranty replacements or repair, defective products should be returned, transportation paid, to the place of purchase, or to American Acrylic & Injection, Inc.

BATHTUB AND SHOWER PAN WARRANTY

BATHTUBS PURCHASED AS FACTORY SECONDS OR SURPLUS ARE SOLD “AS IS” WITH NO WARRANTY

We warranty to the original purchaser and the original user for a time of 2 years with original Proof of Purchase that our bathtubs

1. Will be free from manufacturing defects
2. Will not chip, blister or delaminate

Our liability is limited only to repair or replacement of the product at the point of original purchase F.O.B. Factory. We shall not be held liable for any installation cost, labor or damage incurred from removal or reinstallation. This warranty does not apply to products installed in commercial properties (rental properties, motels, hotels, etc.) This warranty does not apply to whirlpool units or any damage relating to installation of the whirlpool system. Your whirlpool system should be covered under a separate warranty.

All whirlpool and Air massage bathtubs are fully water tested for leaks before leaving the factory. 

This warranty will not apply if:

1. Tub is not installed according to our instructions or not installed according to local building codes and ordinances.
2. If moved from original point of installation.
3. If proper care and customary cleaning instructions are not followed.
4. If bathtub is subjected to abuse, mishandling or accident.
5. Not warranted outside the United States.

RETURNED ITEMS

Customer is responsible for return freight. All returns must be returned in original factory packaging.  All non-warranty returns are subject to a 15% re-stock fee.

Do your bathtubs and whirlpool jet systems include a warranty? Yes. See the warranty information in our Learning Center.